![]() Edits in which a clip’s audio and video have different start or end points are called split edits. You can also use the precision editor to extend the audio in a clip beyond the boundaries of the video-for example, when you want the audio from an outgoing clip to continue during the next video clip, or when you want the audio from an incoming clip to start before the video. You can use the precision editor to fine-tune when your clips begin and end, as well as the duration of transitions between clips. ![]() Import projects created on iPhone or iPad.Modify crop, rotation, or Ken Burns effects.Next we'll take a look at fine tuning your edits for even more precise cuts. And that's how you can trim your clips to clean them up a bit, and how you can also perform slip edits. (footsteps) So let's see much more tight edit that focuses on the action now. So in context with the rest of the project, this is what my clip looks like now. All right, so when you're done here, you can click to close the clip trimmer, and you're back looking at the project, playing with the rest of your clips. Slip editing lets you choose an entirely different section of the footage if you want, but it keeps the overall clip length exactly the same, and therefore won't throw off your timing. Draging the ends of your clip makes your clip a few fractions of a second longer, or shorter, which might not seem like much, but it could throw off the timing of your music, or transitions if you change a lot of clips this way. This is known as slip editing, and it's especially useful to be able to do this if you've already set up music, or transitions to be timed with your video, but you want to make a change to your clip. So I can see exactly how this shot will start, and finish. So you can see on the left the beginning of the frame, and on the right the ending frame. Notice when you drag you get a side by side view in the viewer. Another thing you can do here in the clip trimmer is to click, and drag the entire selection, to change both ends at the same time, while keeping the overall length of the clip the same. So you can see this letting me be a lot more precise. This allows you to be more precise with your trimming, and here you can drag either end of the selection box to add, or remove single frames at a time from the beginning, or end of your clip. So this view shows you the entire clip as a whole, with the part that's actually appearing in the movie highlighted between these two white bars. To get to it, right click on the clip, and choose Show clip trimmer, or use the keyboard shortcut of command backslash. But if you want more precise control in terms of picking exact frames to start, or in the clip, you'll have to use the clip trimmer. In many cases this is all you really need to do to add frames back to the beginning, or end of your clip. Now if you accidentally made the clip too short, or if the clip was too short when you dragged it in, you can deselect it, and just drag the edges to make the clip longer, or shorter again. So with that selection made, I can choose modify, trim selection, or I can press option forward slash, and doing that trims away everything, but what I have selected, and remember you're never damaging your original footage when you do this, the complete uncut version of the footage where this clip came from, is still sitting safely here in the event browser, and again you can see the portion that I used, highlighted in orange. So I'll skim until I come from behind the trees right about there, hold down r and drag to the right, and I'll select until I just run off screen right there. So I'm going to hold down r on the keyboard, and drag to make my selection of the area I want to keep. and I think in this case, I don't need the part at the beginning where I'm hidden by trees, and I also have too much time at the end after I run off screen. For example, after reviewing this clip in my project, where I'm running over this plank bridge, I've decided that it goes on for too long, so there are a couple of ways we can trim this clip, first, I'm going to skim through, and find the portion of the clip I want to keep. As you work on assembling your movie, there going to be a lot of times, when one of the clips you've added turns out to be too long or too short, maybe you accidentally left out some of the good action in the clip, or maybe after looking at the clip in the context of the rest of the movie, you determined that it goes on for too long, but that doesn't mean you have to go back up to the event browser, reselect the clip, and then drag it back in again, all you need to do is trim the existing version of the clip in the project timeline.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |